350-601 Exam: Absolutely Free Online Practice

Question 1
- What is the benefit of adding Cisco HyperFlex Hardware Acceleration Cards to a HyperFlex deployment?
  A : offline encryption acceleration
  
  B : increased network throughput
  
  C : GPU acceleration
  
  D : Increased compression efficiency
  
  Answer: D
Question 2
- A network engineer must configure a Fibre Channel port monitoring for the local port. The source port should be monitored in the ingress direction. Which configuration should be implemented to achieve this objective?
  
  A :
  interface fc1/15 switchport mode SD switchport speed 2000 no shutdown span session 1 destination interface fc1/15 source interface fc1/16 rx
  
  B : interface fc1/15
  switchport mode switchport
  switchport speed 2000
  no shutdown
  span session 1
  destination interface fc1/15
  source interface fc1/16 tx
  
  C : interface fc1/15
  switchport mode fex-fabric
  switchport speed 2000
  no shutdown
  span session 1
  destination interface fc1/15
  source interface fc1/16 rx
  
  D : interface fc1/15
  switchport mode SD
  switchport speed 2000
  no shutdown
  span session 1
  destination interface fc1/15
  source interface fc1/16 tx
  
  Answer: A
Question 3
- A network engineer must deploy a configuration backup policy to the Cisco UCS Manager. The file generated from this backup must have a snapshot of the entire system that should be used to restore the system during disaster recovery. The backup file must be transferred insecurely by using the TCP protocol. Which configuration backup settings meet these requirements?
  A :
  Type: All Configuration
  Protocol: SCP
  
  B :
  Type: Logical Configuration
  Protocol: SFTP
  
  C :
  Type: Full State
  Protocol: FTP
  
  D :
  Type: System Configuration
  Protocol: TFTP
  
  Answer: C
Question 4
- An engineer must perform an initial configuration of VXLAN Tunnel End-Point functionality on the Cisco Nexus 9000 Series platform. All the necessary features are already enabled on the switch. Which configuration set must be used to accomplish this goal?
  A : NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface VLAN10 NX9K(config-if)# ip unnumbered loopback0 NX9K(config)# interface nve1 NX9K(contig-if-nve)# source-interface loopback0
  
  B : NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface overlay0 NX9K(config-if-overlay)# source-interface loopback0 NX9K(config)# interface VLAN10 NX9K(contig-if-nve)# source-interface loopback0
  
  C : NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface tunnel1 NX9K(config-if)# tunnel source loopback0 NX9K(config)# interface ethernet1/1 NX9K(contig-if)# ip unnumbered loopback0
  
  D : NX9K(config)# interface loopback0 NX9K(config-if)# ip address 10.10.10.11/32 NX9K(config)# interface nve1 NX9K(config-if-nve)# source-interface loopback0 NX9K(config)# interface ethernet1/1 NX9K(contig-if)# ip unnumbered loopback0
  
  Answer: D
Question 5
- Refer to the exhibit. An engineer must configure fabric binding on a Cisco MDS 9000 Series Switch to match the output. Which fabric database configuration accomplishes this goal?
  
  A :
  
  B :
  
  C :
  
  D :
  
  Answer: D

Free Cisco 350-601 Exam Questions

Absolute Free 350-601 Exam Practice for Comprehensive Preparation